|
Stop paying to ship air. In the glass distribution game, your "cull rate" (breakage) and your return logistics costs are the two silent killers of your margin. If you are still using disposable wood crates that warp, or cheap A-frames that peel rubber in the California sun, you are bleeding efficiency. It’s time to upgrade to a system designed for high-velocity Wholesale Tempered Glass and IGU logistics. |
For any Glass Distributor or Glazing Contractor, the outbound shipment is only half the battle. The real headache begins when the truck returns. Traditional A-frame racks are stable, yes, but they are space hogs. A 53-foot trailer returning with empty A-frames is essentially shipping air.
Our Reusable packaging steel glass racks utilize a smart L-Shape Nesting Design. The geometric offset at the base allows empty racks to slide into one another, much like shopping carts.
Empty racks nested to save 70% of floor space during return transport.
The Operational Impact:
In the world of Tempered Glass and high-value Insulated Glass Units (IGUs), a scratch on the Low-E coating or a chipped edge means the unit is scrap. The weakest link in most generic racks is the glue.
Most competitors use adhesive to attach the rubber protection strips. In high-heat environments—like a truck bed in Sacramento or a non-climate-controlled warehouse—that glue fails. The rubber slides off, exposing the raw steel. When 2,000 lbs of glass shifts against bare steel during braking, the result is catastrophic.
Steel-core EPDM rubber mechanically fixed with self-tapping screws—no glue failure.
Our Engineering Solution:
Whether you are moving crates of raw Float Glass or bundles of heavy Laminated Glass, rigidity is non-negotiable. A rack that flexes during transport transfers stress directly to the glass sheets, causing invisible micro-fractures that lead to delayed breakage.
We manufacture our Reusable packaging steel glass racks using Q235 Carbon Structural Steel (equivalent to ASTM A36). Crucially, we use Full Seam Welding throughout the structure. We do not "stitch weld" or spot weld the critical load-bearing joints.
Heavy-duty welded structure supporting massive curtain wall glass units.
This results in a Working Load Limit (WLL) that comfortably handles 3,000 to 8,000 lbs depending on the specific model, ensuring that the rack absorbs the road vibration, not your expensive inventory.
Double handling is the enemy of efficiency. The risk of breakage increases every time you transfer a glass sheet from a factory harp rack to a shipping pallet.
Our racks are designed for Four-Way Forklift Access and include certified Crane Lifting Lugs. This means the same rack can be loaded at the end of your tempering line, moved by forklift to the warehouse, loaded onto a flatbed or curtain-sider truck, and then lifted by a tower crane directly to the installation floor at the construction site.
Engineered with reinforced forklift channels for safe internal logistics.
1. Can these racks handle Jumbo Size (130" x 204") sheets?
Yes, we manufacture oversized versions specifically for Jumbo and Split-Jumbo sheets. We reinforce the base and increase the vertical post dimensions to 60x60mm or larger to prevent deflection under the immense weight of large-format architectural glass.
2. We have a mixed inventory of IGU and raw float glass. Can we mix them?
Ideally, raw glass (packs) and loose IGUs should be separated for safety. However, our racks feature a specific 3-5 degree tilt. This angle is calculated to safely hold single sheets (IGUs) without tipping, while the robust base can support full packs of raw glass if strapped correctly.
3. Will the powder coating survive outdoor storage in coastal areas?
Standard powder coating (RAL 5010) is suitable for indoor and transit use. If your yard is located in a coastal region or high-humidity area, we strongly recommend our Hot-Dip Galvanized finish. This provides sacrificial anode protection, preventing rust even if the steel is scratched, ensuring a 15+ year lifespan.
4. How many empty racks fit in a standard 53' truck?
Thanks to the L-Shape nesting design, you can typically fit between 80 to 100 empty racks in a standard 53' dry van, depending on the specific width of the model selected. This maximizes your reverse logistics efficiency.
5. Can you add casters for "man-handling" inside the shop?
Yes. While the standard transport racks are designed for forklifts, we offer "shop cart" versions (Lmrack) equipped with heavy-duty phenolic or polyurethane casters (2 swivel, 2 rigid) for manual movement around glazing lines and cutting tables.
