🏭 Steelpallet · Diretto dalla Fabbrica · Disponibile OEM

Mtrack Motorcycle Pallet Rack: Design Revisions, Locking Pins and Stacking Verification

Mtrack motorcycle pallet rack technical solution: tube and hook revisions, pallet-jack lifting clearance, 19 mm locking pins, 220 MPa allowable stress at 500 kg and 20 ft / 40 ft HC loading plans.

100%
Qualità dell'Acciaio
Pesante
Capacità di Carico
Personalizzato
Misure Realizzate
Mtrack Motorcycle Pallet Rack: Design Revisions, Locking Pins and Stacking Verification
Technical Solution — Mtrack Motorcycle Pallet Rack

Mtrack Motorcycle Pallet Rack: Design Revisions, Locking Pins and Stacking Verification

A documented engineering review of the Mtrack motorcycle shipping pallet: tube and hook revisions, pallet-jack lifting clearance, 19 mm locking pins, nameplate position, 220 MPa allowable stress under a 500 kg load, and 20 ft / 40 ft high-cube loading plans.

Discuss Your Rack Design

Mtrack technical source image

Customer feedback:

See the customer feedback Word document

Corresponding modifications

Overall effect after modification

Mtrack technical source image
Mtrack technical source image

Move four tubes and remove part of the metal mesh (on one side only)

Mtrack technical source image

Move four hooks

Mtrack technical source image

Replace the 4 bolts with standard locking pins

Add 4 locking pins with wire to each upright post

Mtrack technical source image
Mtrack technical source image

Raise the structure by 1'' so that the rack can be lifted with a standard pallet jack (3.75'' clearance)

Mtrack technical source image

Add 2 lifting fork channels, made with thicker material and stronger welding

Mtrack technical source image
Mtrack technical source image

Optional wheel chock (position must be adjustable)

Mtrack technical source image
Mtrack technical source image

It can be designed and added in the form of the chock shown in the picture

Galvanizing option: cold galvanizing can be applied to the whole unit, with a zinc layer of about 10 μm. Hot-dip galvanizing is not recommended, because the very high temperature of hot-dip galvanizing will cause the rack structure to deform.

Option of carrying 2 motorcycles per rack: this function cannot be realized at present

Modify the existing basis (folding structure); only two changes are needed;

-According to the sketch below, the opening needs to be increased to 760 mm

-The distance from the outside of the frame to the center of the 4 hooks should be 130 mm.

Mtrack technical source image
Mtrack technical source image
Mtrack technical source image

Customer question:

Regarding the wheel chock, how is the position fixed when the rack is placed on the ground? That is why I would prefer to adjust it on the vertical wall. Can the front end be made foldable, as on the model we currently use? (see the blue model)

Mtrack technical source image

Our reply:

Your design is more thorough than our original model, and we can fully manufacture the motorcycle wheel fixing part with reference to your design. You can send us the 3D solid model so that we can see how it can be better connected to our existing motorcycle pallet.

Mtrack technical source image

With the current design, a 40 ft high-cube container can hold 90 units and a 20 ft container 32 units. The final loading quantity still depends on whether our wheel fixer affects loading. We are also very willing to share drawings with you to facilitate the final confirmation of the design.

Mtrack technical source image
Mtrack technical source image
Mtrack technical source image
Mtrack technical source image
Mtrack technical source image
Mtrack technical source image
Mtrack technical source image
Mtrack technical source image

New requirements, 10 April 2024:

After internal discussion, the wheel chock may not be needed.

As for the locking pins, we used the type you suggested in the past, but it is now prohibited because the clips break easily. As shown in the picture below, each rack needs 8 pins, because sometimes we need to remove both sides completely, and the bottom pins you suggested are difficult to remove in winter while wearing gloves.

Mtrack technical source image

In addition, lifting the two sides is not smooth. Could you make the radii at the top and bottom larger, as shown in the picture below?

Mtrack technical source image

Finally, we modified one rack according to the latest concept, and the tubes in the middle are very weak. Is it possible to make these tubes the same size as the outer tubes? I think we can remove two short tubes.

Mtrack technical source image

Update, 6 May:

Could you add the allowable maximum stress point and the possible maximum stacking quantity to the Word document?

In addition, could you send me the simulation report of the original rack design? I would like to compare it with the previous design.

Mtrack technical source image

As for the ID nameplate, please place it on the outer tube as shown in the picture below

Mtrack technical source image

;

As for the locking pins, can we use pins with a diameter of 19 mm? Or, as a second option, can we change to another type of clip;

Mtrack technical source image

Reply to the 6 May update:

Mtrack technical source image

The allowable maximum stress of the current rack is 220 MPa. Under a 500 kg load, the maximum value of 181 MPa occurs in the U-shaped plate where the motorcycle wheel sits. The maximum stacking height of the motorcycle rack is limited by the stability of the hinge parts; the total stacking height is generally recommended to be ≤6 m. At the current height of our motorcycle rack, 4 stacking layers are recommended.

Mtrack technical source image

This is the test result before the two middle beams were modified: the maximum stress value becomes 203 MPa. With the rest of the structure unchanged, this shows that the maximum stress point appears on the two long middle beams.

The nameplate position is fine. We will pre-drill the holes and then fix it with rivets.

Mtrack technical source image

19 mm pins are acceptable, which fully meets the requirement; the effective length needs to be 70-75 mm

Mtrack technical source image

Container loading plan:

Mtrack technical source image

20 ft container: 7 units per stack, 4 stacks, 28 units in total

Mtrack technical source image

40 ft high-cube container: 8 units per stack, 10 stacks, 80 units in total

Share your wheel fixture drawings, 3D model or loading constraints with our engineering team. We will review hook positions, locking pin diameter and effective length, pallet-jack clearance and stacking height, and confirm the Mtrack motorcycle pallet rack configuration against your requirements. Contact Steel Pallet

Richiedi Dettagli Prezzi




    Richiedi Listino Preventivi

    La tua lista di richieste di preventivo è vuota.

    Request Technical Drawings

    Provide your contact details to request the drawing. If a file is unavailable, our team will contact you.