L-Shape Glass Storage Rack: Structure, Load Parameters and Quality Control
Grack
Grack L-shape glass storage rack: 2000×1135×2100 mm, 2000 kg load, Q235 carbon steel frame, removable flat rubber strips, RAL5010 powder coating, full-penetration welding, four inspection levels.
L-Shape Glass Storage Rack: Structure, Load Parameters and Quality Control
This technical solution documents the Grack steel glass storage rack: a welded carbon steel frame built from 100×50×2.5 and 50×50×2.0 square tubes with full-penetration joints, 2000 kg load capacity, 2000×1135×2100 mm external dimensions, removable flat rubber strips, and RAL5010 powder coating checked against a RAL color card across four inspection levels.

Technical Solution
Structure Introduction
This steel glass rack consists of two parts: the rack body and the rubber strips. All materials used are high-quality carbon structural steel tubes. The tube specifications are 100×50×2.5 square tube and 50×50×2.0 square tube. Every welded joint is a full-penetration structure, so the rack is structurally stable and has a high load capacity. The rubber strips are removable, which makes later replacement convenient.

Figure 1 — Rack body

Attributes and Parameters
Basic attributes
| Nombre del producto | Grack | |
|---|---|---|
| External dimensions | 2000*1135*2100 | Customizable ☑ |
| Product material code | Not available yet | |
| Tratamiento de superficie | Electrostatic powder coating | Customizable ☑ |
| Surface color | Azul | Customizable ☑ |
| Product dead weight | Approx. 170 kg | Customizable ☑ |
| Total weight of rubber strips | Approx. 15 kg | |
| Rubber strip type | Flat | |
| Product load capacity | 2000 kg |
|
| Raw material | Carbon steel Q235 | |
| Main raw material specifications | Hot-rolled plate t=5 mm | |
| Square tube 100*50*2.5 | ||
| Square tube 50*50*2.0 |
Packaging and Transport
Packaging method
Each rack is wrapped in stretch film.
Transport plan
Existing problem: the racks cannot be stacked when empty, which affects transport.
Sample Drawing

Quality Acceptance Standards and Delivery Plan
| Categoría | Customer requirement | Corresponding technical interpretation | Quality control and inspection | Inspection tool | Inspection date | Inspection level |
|---|---|---|---|---|---|---|
| Cutting Fit-up |
External dimension 2000*1135*2100 | Key product dimension; according to the production drawing dimensions and tolerance requirements; dimensions without specified tolerance follow Class C of GB1804-2000 | Measure the length of all parts of the product; the measured results must meet the drawing requirements. Then, with every 50 cuts as a node, sample part dimensions again to check whether they are compliant; | Tape measure, measuring accuracy 1 mm | Ⅰ | |
| Measure the dimensions of the parts formed at the first fit-up of each fixture set; the measured results must meet the drawing requirements; | Tape measure, measuring accuracy 1 mm | Ⅰ Ⅱ Ⅲ Ⅳ | ||||
| Welding | / | All tube interfaces are fully welded | After the first article of each welding operator is completed, inspect according to the welding positions specified in the drawing; there must be no missed welds (a gap of ≥8 mm at a specified welding position counts as a missed weld) | Tape measure, accuracy ≥1 mm | Ⅰ Ⅱ | |
| The weld leg height shall be greater than the base material thickness of the thinnest part | Vernier caliper, accuracy 0.1 mm | Ⅰ | ||||
| Grinding | / | All welds must be ground | All welds are ground smooth within 3 cm to the left and right, with no welding slag | / | Ⅰ | |
| Recubrimiento | Surface treatment: powder coating | Blue RAL5010 | Compare the color against the RAL color card; there shall be no obvious color difference | RAL color card | Ⅰ Ⅱ Ⅲ Ⅳ | |
| / | Ⅰ Ⅱ Ⅲ Ⅳ |
Inspection levels
Ⅰ — Operator
Ⅱ — Quality inspector
Ⅲ — Production supervisor
Ⅳ — Customer
Customers may take part in all inspection levels, and all results are provided to the customer.
The Grack L-shape glass storage rack is built around 2000×1135×2100 mm external dimensions, 2000 kg load capacity and removable flat rubber strips, with customizable color, surface treatment and dimensions. Send the glass panel sizes, thickness range and handling method you work with, and our engineering team will return a configuration, drawing confirmation and inspection plan. Contact SteelPallet Engineering