🏭 Steelpallet · Factory Direct · OEM Available

AGrack Glass Storage Transport Rack: Technical Solution for Customer Sample Detail Adjustments

Technical solution for the Agrack collapsible glass storage transport rack: leg protector limit blocks, 1 mm slot clearance, 750/798 mm upright holes.

100%
Steel Quality
Heavy
Duty Rating
Custom
Sizes Built
AGrack Glass Storage Transport Rack: Technical Solution for Customer Sample Detail Adjustments
Agrack · SteelPallet Technical Solution

AGrack Glass Storage Transport Rack: Technical Solution for Customer Sample Detail Adjustments

Following the customer's review of the first sample, eight detail adjustments were requested for the Agrack collapsible glass storage transport rack: two limit stop blocks on top of the leg protector, tighter slot-to-flat-key clearance (1 mm per side), an inner limit stop block, a centered wire-tying structure on the long-side bottom tube, smooth grinding of the spliced base plate gap, flat rubber padding on the movable bar, two new upright holes at 750 mm and 798 mm from the ground, and a deepened U-shaped slot with an adjusted side-door cross bar height of 877 mm instead of 860 mm.

AGrack glass storage transport rack technical solution source image 01

Customer Requirement Analysis:

Background: a sample of this product was first made for the customer. The customer considered the overall result good, but raised specific adjustments to local details and added several new requirements, as follows:

Add two limit stop blocks to the top of the leg protector to restrict left-right and front-back displacement.

Reduce the clearance between the upper slot of the leg protector and the flat key of the upright appropriately.

Add a limit stop block on the inner side of the leg protector, but it must not affect folding and stacking.

Add a wire-tying structure centered on the long-side bottom tube.

Grind the gap between the two spliced base plates smooth.

Add flat rubber padding to the movable bar as well.

Add two holes to the upright, at heights of 750 mm and 798 mm from the ground respectively.

Deepen the U-shaped slot to make taking out and putting back the movable bar easier.

Technical Solution Description

1. Add two limit stop blocks to the top of the leg protector to restrict left-right and front-back displacement, without affecting folding and stacking.

AGrack glass storage transport rack technical solution source image 01

2. Reduce the clearance between the upper slot of the leg protector and the flat key of the upright appropriately (the clearance between the slot and the flat key is only 1 mm per side).

AGrack glass storage transport rack technical solution source image 02

3. Add a limit stop block on the inner side of the leg protector, but it must not affect folding and stacking.

AGrack glass storage transport rack technical solution source image 03

A limit stop block with a height of 8 mm can be added, but adding a block at this position is not recommended, because it would make insertion and removal difficult; a limit block has already been added above, so adding another one here does more harm than good.

4. Add a wire-tying structure centered on the long-side bottom tube.

AGrack glass storage transport rack technical solution source image 04

A 40×40 square tube is welded centered at this position, 20 mm high, on both sides.

5. The gap between the two spliced base plates will be emphasized and required to be ground smooth during production.

6. Add flat rubber padding to the movable bar as well.

AGrack glass storage transport rack technical solution source image 05

7. Add two holes to the upright, at heights of 750 mm and 798 mm from the ground respectively.

AGrack glass storage transport rack technical solution source image 06
AGrack glass storage transport rack technical solution source image 07

8. While deepening the U-shaped slot, adjust the position of the side-door connecting beam appropriately so that the movable bar has sufficient space for taking out and putting back.

AGrack glass storage transport rack technical solution source image 08
AGrack glass storage transport rack technical solution source image 09
AGrack glass storage transport rack technical solution source image 10
AGrack glass storage transport rack technical solution source image 11
AGrack glass storage transport rack technical solution source image 12

Because two new holes are added, and in order to ensure the movable bar can be taken out and put back normally, the height of the side-door cross bar from the ground on the original sample will be adjusted from 860 mm to 877 mm. Please confirm whether this is acceptable.

Request Pricing Details




    Request Quote List

    Your quote request list is empty.

    Request Technical Drawings

    Provide your contact details to request the drawing. If a file is unavailable, our team will contact you.