Vertical Pipe Storage Rack for 4 m Plastic Pipes: 4-Layer Stackable Technical Solution
derack
Technical solution for a vertical pipe storage rack holding 4 m plastic pipes of 100–150 mm diameter: 2900×1130×1040 mm rack, 990 kg design load, 4-layer stacking, fork and packing details.
Vertical Pipe Storage Rack for 4 m Plastic Pipes with 4-Layer Stacking
An engineering solution for a warehouse that needed to raise space utilization: a plug-in stacking frame for 4 m plastic pipes of 100–150 mm diameter and about 20 kg each, stacking four layers high, with a designed load of 990 kg per rack. Dimensions, fork pockets, material sections, container loading and risk controls are documented below.

Customer Requirement Analysis:
The customer wanted to improve warehouse space utilization and chose our plug-in structure pipe stacking rack.
The plastic pipes to be stored are 4 m long, with a diameter of approximately 100–150 mm.
Each pipe weighs about 20 kg.
The length, width and height of the rack can be configured reasonably on our side.
For indoor warehouse use, a powder coating finish can be applied for corrosion protection.
Stacking target: 4 layers.
Figure 1:

Technical Solution Description
The preliminary design form of the pipe rack is shown in the figure below.

Grey part – pipe rack; blue part – simulated pipes.
The outer dimensions of the rack are 2900 × 1130 × 1040 mm.

The center distance of the fork entry apertures is provisionally 930 mm (750 + 180); whether this dimension is suitable must be confirmed when the final solution is fixed. The rack is 2900 mm long, which leaves 550 mm of space at each end beyond the stored pipes, so that ropes can be tied at both ends of the pipes for lifting operations.

The height of the fork entry aperture is 80 mm and its width is 180 mm, as can be seen in the previous figure; fork tines of forklifts rated up to 5 t can pass through smoothly.

These are all the key dimensions of the rack.

We simulated a storage result with Φ150 mm pipes placed in the rack. With the current specification, 33 pipes can be stored; at 20 kg per pipe, the load required for a single rack is at least 33 × 20 = 660 kg. For safety we set a safety factor of 1.5, so our design load is 660 × 1.5 = 990 kg.

Based on the load requirement above and on the material specifications of similar products we have produced before, we defined the section and thickness of each component. The main load-bearing beams adopt 100 × 50 × 3 rectangular tubes, and the uprights adopt 60 × 60 × 2 rectangular tubes.


After four-layer stacking, the fork aperture of the topmost rack is 3107.5 mm above the floor. This is not especially high for forklifts rated up to 3 t, but it still needs to be confirmed whether your forklift can lift to such a height.

Rendering of the four-layer stacking effect.
Packing and Loading Plan
Empty stacking of 10 layers: height 2550 mm.
Loading quantity in a 40 ft high cube container: 80 units.
Loading quantity in a 20 ft container: 32 units.

Packing reference:



Products are packed with stretch film plus strapping bands. This method does not generate extra packing cost, but it cannot fully prevent surface paint film damage caused by collisions between products during transport. A more dependable wooden crate packing is also available, and the crate is fully calculated into the product cost at our purchasing price (wooden crate price = 90 RMB/㎡).
Implementation Plan and Lead Time
The sales representative can provide this content when the customer has specific quantity and production lead-time requirements.
After-Sales Service Plan
None.
Risk Assessment
When the forklift enters and lifts the forks, operation must be carried out at uniform speed; violent fork handling must be avoided so that the product is not damaged and its use is not affected.
Regularly inspect the base, uprights and other components for bending, deformation, weld cracking and similar problems, so as to avoid danger caused by problems in rack components.
During static stacking, the operator must confirm that the feet of the upper rack have indeed landed fully on the uprights of the lower rack before releasing it, so as to avoid the danger of a stack collapse caused by improper stacking.
Send us your pipe or conduit length, diameter, weight per piece, required stacking layers and forklift capacity, and we will size the vertical storage rack, fork pockets and load rating for your layout. Steel Pallet manufactures this plug-in stacking pipe rack in steel-pallet.com production. Send your pipe storage requirements