40ft High-Cube belading: waarom Mytrack-projecten 32 of 64 opvouwbare stillages laden

How many foldable Mytrack stillages fit in a 40ft high-cube container? The only safe answer is: it depends on the project configuration. Two real project files show why a single container count can be misleading for an export buyer. Project 14922 was recorded at 32 stillages per 40ft high-cube container. Project 14652 was recorded at 64 stillages per 40ft high-cube container. These are not two claims for one standard loading capacity. They are separate configuration files.

If you are planning a shipment, use the count only after the stillage dimensions, the folded state, the stacking arrangement, the packaging and the securing method have been assessed together. Foldable stillages can reduce the return volume, but "foldable" does not remove the need for a project-specific loading plan.

Why the two project files show 32 and 64

File 14922 came from a motorcycle transport configuration. The recorded external dimensions were 2300 × 2470 × 1270 mm, with an internal loading surface of 2116 × 2410 mm. Each stillage weighed 300 kg, had a 100 mm forklift opening and could be reduced to 355 mm when folded. The uprights could be pulled up and folded inward. The project file specifies a stack of eight stillages at 2560 mm and a loading result of 32 stillages in a 40ft high-cube container.

This configuration is built around the space and handling needs of motorcycle transport. The upright geometry, usable internal surface area and forklift access are part of the shipping specification, not details that can be separated from the container count. A different load, frame height, upright arrangement or protective packaging can produce a different result.

Why file 14652 reaches 64

File 14652 describes a different foldable stillage project. The documented empty arrangement is eight folded stillages in one stack, with a recorded loading result of 64 stillages in a 40ft high-cube container. The file also identifies packaging options: stretch film with straps, or wooden crates priced at 90 RMB per square meter. Those details are important because the space taken up by the packaging and the clearance needed for loading can change the final arrangement.

The figure of 64 stillages therefore belongs to the folded stacking and packaging method of that project. It must not be combined with the motorcycle rack file 14922, averaged into a "typical" capacity, or used as a promise for an unassessed design. The difference is not a contradiction. It is evidence that the loading quantity follows the physical configuration.

How to plan a loading table for a 40ft high-cube

Start with the exact product configuration. Confirm the external and internal dimensions, the folded height, whether the uprights are removed or folded inward, and the number of units in each stack. Then define the packaging method before counting the available positions. Film and straps may use less volume than a wooden crate, while a crate may offer a different protection and securing arrangement. Do not assume the packaging allowance is zero.

Then check the handling route. Forklift access, container door clearance, stack stability and access for lashing straps must work at the same time. For the type 14922 application, the 100 mm fork opening and the 355 mm folded height are useful planning inputs, but they do not replace a loading drawing. For another project, the confirmed folded stack height and packaging enclosure take priority.

Finally, set up a project-specific loading table with units per stack, stack height, packaging allowance, loading orientation and total units. If the configuration changes, the table must be recalculated. A standard flat steel pallet or a non-foldable rack may be unsuitable when the load requires special positioning, vertical storage or compact empty returns.

Where Mytrack fits — and where it does not

• Use foldable stillages when return volume in the empty state, vertical storage and repeated mechanical transport are part of the logistics plan.
• Use a motorcycle transport configuration only when the load dimensions, support points and securing requirements have been confirmed for the motorcycle load.
• Consider hinged rails, removable uprights or other securing details only when they are included in the approved configuration; a product image is not a substitute for a drawing.
• Do not use one published container count for rolling doors, motorcycles and general goods. Irregular loads, protective packaging and access requirements each require their own loading assessment.

FAQ: Mytrack container loading quantity

How many Mytrack stillages fit in one 40ft high-cube container?

There is no universal number. The verified project records available here are 32 units for project 14922 and 64 units for project 14652. Each figure belongs to its own configuration and packaging setup.

What should I send before asking for a loading plan?

Send the required external and internal dimensions, folded height, upright arrangement, load type, stack quantity, packaging choice and securing method. If the load is a motorcycle or another irregular load, add the support and securing requirements. With these input data, the loading table can be built rather than copied from an unrelated project.